Search:

Type: Posts; User: Jet-Lee; Keyword(s):

Page 1 of 20 1 2 3 4

Search: Search took 0.06 seconds.

  1. Replies
    8
    Views
    656

    As you tested should still give DC voltage...

    As you tested should still give DC voltage readouts. If you're at zero, your TPS is toast.
  2. Replies
    8
    Views
    656

    Are you sure the needle jet (collar) is installed...

    Are you sure the needle jet (collar) is installed in the correct orientation? It's the piece the needle slides into. One end is flat, one is concave. The concave end should be pointing up into the...
  3. Replies
    1
    Views
    176

    "The cnc files" will vary greatly from machine to...

    "The cnc files" will vary greatly from machine to machine.

    If you're meaning the dwg/dwf used to create the cnc files, that should be much easier to find.
  4. Replies
    8
    Views
    656

    Sounds like your fuel valve in the carb bowl...

    Sounds like your fuel valve in the carb bowl might be clogged or dirty, not letting enough fuel in. Also check that the bowl vent is clear (top left hole when looking at the carb).
  5. Replies
    5
    Views
    591

    I see he put 44903 as his location, that's...

    I see he put 44903 as his location, that's Ontario.
  6. Replies
    5
    Views
    591

    Looks clean! Add the Pro-Series and have fun...

    Looks clean!

    Add the Pro-Series and have fun with it!
  7. Replies
    8
    Views
    656

    Replace gas with new. Make sure the needle jet...

    Replace gas with new. Make sure the needle jet (collar) is installed in the correct direction. Chech and/or adjust your auto-enricher. Check/adjust your TPS per FSM.

    Links:
    BuellMods for manuals...
  8. Replies
    205
    Views
    155,326

    Sticky: Harley is a bunch of bitches. I would've given...

    Harley is a bunch of bitches.

    I would've given you my VIN, lol.

    Glad you're back in business!
  9. Replies
    635
    Views
    93,142

    Sticky: Poor thing's still sitting. All my attention goes...

    Poor thing's still sitting. All my attention goes to my other bikes, due to them being my rides to/from work.
  10. Replies
    158
    Views
    35,461

    Going to put some 12:1 Wiseco pistons in it. 60k...

    Going to put some 12:1 Wiseco pistons in it. 60k miles on it right now, could use some new rings; need to rebuild the top-end anyways with fresh gaskets.
  11. Replies
    15
    Views
    7,741

    Working on getting the bars lowered. Can't go...

    Working on getting the bars lowered. Can't go with RX top triple as it interferes with the SX dash. Trying to just do some clip-ons while leaving the SX triple, but I may get conflict with my...
  12. Replies
    17
    Views
    2,941

    I've reused them without issue.

    I've reused them without issue.
  13. Replies
    17
    Views
    2,941

    eBay contest? Cool dude!

    eBay contest? Cool dude!
  14. Replies
    17
    Views
    2,941

    Using an XB9 piston with a stock head will run...

    Using an XB9 piston with a stock head will run worse, as the dome and squish are shaped differently.

    I believe the Blast uses a Thunderstorm piston with a Lightning head, so if you find a front...
  15. Also, here's a PDF of Andrews installation...

    Also, here's a PDF of Andrews installation instructions.

    http://www.andrewsproducts.com/files/assets/Blast-1.pdf
  16. There should be an arrow on the top of the...

    There should be an arrow on the top of the piston. Orient the piston to point towards the front wheel.

    If there is no arrow, then the larger valve relief is the intake, which is at the rear.

    If...
  17. Jumper the kickstand safety switch, flip the...

    Jumper the kickstand safety switch, flip the middle diode in the fuse box and try again.
    If that still doesn't do it, clean all grounds thoroughly.
    If still having the issue after that, then...
  18. DMV messed up, maybe? What's your VIN? My 1988...

    DMV messed up, maybe? What's your VIN?

    My 1988 RX7 was titled and smogged as 87.I pointed out the VIN sticker and asked, "How can it be an 87 if it wasn't produced until Jan 1988?"
  19. Replies
    3
    Views
    1,809

    Wow, didn't realize it's been so long.

    Wow, didn't realize it's been so long.
  20. Replies
    17
    Views
    2,941

    I've always liked the chopper Blasts. I'd...

    I've always liked the chopper Blasts. I'd probably never build or ride one, but I think the builds are neat to follow.
  21. Replies
    15
    Views
    7,741

    Wow, so much has happened since this. I'll piece...

    Wow, so much has happened since this. I'll piece it together...

    The shop, Bay Area Racing (owned and operated by Dean Hodel) did not show up to the court hearing and I won a default judgement. He...
  22. Replies
    20
    Views
    5,821

    Nice. Plug wires can be a real pain to diagnose.

    Nice. Plug wires can be a real pain to diagnose.
  23. Well that was unexpected, lol. Glad it was a...

    Well that was unexpected, lol. Glad it was a simple fix!
  24. Replies
    7
    Views
    8,595

    hot chip-seal will destroy a tire VERY fast

    hot chip-seal will destroy a tire VERY fast
  25. Thread: Stlouis here

    by Jet-Lee
    Replies
    4
    Views
    6,198

    Nice job getting around the spam blocks, with an...

    Nice job getting around the spam blocks, with an email like that.

    Shoot me a PM verifying your information or I will ban you, your email domain, and all IPv4/v6 addresses from which you registered...
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4