Search:

Type: Posts; User: Jet-Lee; Keyword(s):

Page 1 of 20 1 2 3 4

Search: Search took 0.12 seconds.

  1. An ignition module? Sure. A Blast ignition...

    An ignition module? Sure. A Blast ignition module? They were my go-to. I'll check my garage, but no promises, I might've sent it on already. Have you checked Buellsterparts.com?
  2. Harley sucks in general. St Paul H-D still sells...

    Harley sucks in general. St Paul H-D still sells Buell parts, and the ignition module.
  3. Blow backwards into your fuel line, so air...

    Blow backwards into your fuel line, so air bubbles in the tank. You might've gotten crap clogged in your petcock. Requires complete removal to properly clean, but this will tell you if that's the...
  4. Replies
    2
    Views
    341

    The bolt in the third photo is the pin that holds...

    The bolt in the third photo is the pin that holds the brake pads in.
  5. Have you checked your boot connecting to the...

    Have you checked your boot connecting to the manifold? Sounds like it's torn.
  6. This is interesting. I've always blown out that...

    This is interesting. I've always blown out that hole with carb cleaner so I know mine wasn't plugged. Will add this to the troubleshooting checklist for sure.
  7. Replies
    10
    Views
    594

    Sticky: I found the Yost needles to be too rich, in the...

    I found the Yost needles to be too rich, in the end. Try going back to the stock needle and see how that does.
  8. Replies
    10
    Views
    594

    Sticky: I would aim for the lean side of Styx's chart. ...

    I would aim for the lean side of Styx's chart.

    The Blast has a crappy combustion chamber (15ļ piston, 10ļ head) that requires it to run rich to prevent knock. If you had piston/head work done with...
  9. Replies
    10
    Views
    594

    Sticky: White and Blue are for optional external uses....

    White and Blue are for optional external uses. Just cap those and you have everything hooked up properly.

    Remember this is a single cylinder, so at idle or low rpm it may be a little erratic due...
  10. Replies
    11
    Views
    804

    Looks good!

    Looks good!
  11. Replies
    4
    Views
    394

    I'll try to get some pics, that frame is in...

    I'll try to get some pics, that frame is in storage now. The cowl slips over the seat, and uses the seat for mounting. You absolutely could bolt it down, but it wouldn't operate with the key like a...
  12. Replies
    4
    Views
    394

    Seat cowl on the bare frame? Not without a...

    Seat cowl on the bare frame? Not without a passenger seat for it to cover.

    You're going to have to fab mounts for the subframe to mount to the Blast frame, just FYI.
  13. Thread: muffler mods

    by Jet-Lee
    Replies
    26
    Views
    13,756

    Stumbled across this looking for something else,...

    Stumbled across this looking for something else, thought I'd weigh in...this is one of the best sounding mufflers I've heard on an XB.
  14. Replies
    2
    Views
    980

    A vac leak will also cause the popping on decel...

    A vac leak will also cause the popping on decel and no amount of turning out the pilot will stop that.
  15. Thread: Throttle

    by Jet-Lee
    Replies
    7
    Views
    1,140

    There's no a/f sensor on a Blast. Did you put a...

    There's no a/f sensor on a Blast. Did you put a jumper in the kickstand switch plug?
  16. Thread: Throttle

    by Jet-Lee
    Replies
    7
    Views
    1,140

    Smaller side? You want the long side up. The...

    Smaller side? You want the long side up. The short side has the end flat, the long side has the end angled-in. You want the angled-in side facing up into the carb throat.
  17. Thread: Throttle

    by Jet-Lee
    Replies
    7
    Views
    1,140

    Are you sure the needle jet collar was installed...

    Are you sure the needle jet collar was installed in the correct direction? It should be poking up into the throat of the carb about 1/8"

    Unplug your sidestand switch, stick a wire between the...
  18. Replies
    36
    Views
    19,809

    Looking forward to the rest of the build!

    Looking forward to the rest of the build!
  19. Replies
    178
    Views
    27,150

    Sticky: Yes, you would have to get the USB adapter as...

    Yes, you would have to get the USB adapter as well. $20 is cheaper than I was able to DIY it.
  20. Replies
    178
    Views
    27,150

    Sticky: Yeah, you don't have to connect the rear signal...

    Yeah, you don't have to connect the rear signal wire to the coil. Though if it is connected, you have to ground the plug wire or it fries the coil.

    I'll find the software, at the time it was free,...
  21. Replies
    178
    Views
    27,150

    Sticky: You ordered an Ultima? Lets work through any...

    You ordered an Ultima? Lets work through any issues here, so we can document any/all installation woes.

    If you'd rather, though, you can always hit me up on Facebook. I changed my FB name to...
  22. Replies
    10
    Views
    2,807

    Did they give details? Because that sounds silly....

    Did they give details? Because that sounds silly.

    Adjust your enrichener per my video. You can also power on the motorcycle and watch whether the enrichener closes or not.

    Video link:...
  23. Thread: No spark

    by Jet-Lee
    Replies
    2
    Views
    1,941

    Your BAS sensor could be your issue. Unbolt it...

    Your BAS sensor could be your issue. Unbolt it and shake it around, then put it back at normal position.

    It's a little steel ball inside that can get stuck in a "tipped" position. A good hard...
  24. Replies
    10
    Views
    2,807

    As you tested should still give DC voltage...

    As you tested should still give DC voltage readouts. If you're at zero, your TPS is toast.
  25. Replies
    10
    Views
    2,807

    Are you sure the needle jet (collar) is installed...

    Are you sure the needle jet (collar) is installed in the correct orientation? It's the piece the needle slides into. One end is flat, one is concave. The concave end should be pointing up into the...
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4