Search:

Type: Posts; User: Jet-Lee; Keyword(s):

Page 1 of 20 1 2 3 4

Search: Search took 0.06 seconds.

  1. Thread: muffler mods

    by Jet-Lee
    Replies
    26
    Views
    11,153

    Stumbled across this looking for something else,...

    Stumbled across this looking for something else, thought I'd weigh in...this is one of the best sounding mufflers I've heard on an XB.
  2. Replies
    2
    Views
    399

    A vac leak will also cause the popping on decel...

    A vac leak will also cause the popping on decel and no amount of turning out the pilot will stop that.
  3. Thread: Throttle

    by Jet-Lee
    Replies
    7
    Views
    494

    There's no a/f sensor on a Blast. Did you put a...

    There's no a/f sensor on a Blast. Did you put a jumper in the kickstand switch plug?
  4. Thread: Throttle

    by Jet-Lee
    Replies
    7
    Views
    494

    Smaller side? You want the long side up. The...

    Smaller side? You want the long side up. The short side has the end flat, the long side has the end angled-in. You want the angled-in side facing up into the carb throat.
  5. Thread: Throttle

    by Jet-Lee
    Replies
    7
    Views
    494

    Are you sure the needle jet collar was installed...

    Are you sure the needle jet collar was installed in the correct direction? It should be poking up into the throat of the carb about 1/8"

    Unplug your sidestand switch, stick a wire between the...
  6. Replies
    36
    Views
    17,250

    Looking forward to the rest of the build!

    Looking forward to the rest of the build!
  7. Replies
    178
    Views
    25,348

    Sticky: Yes, you would have to get the USB adapter as...

    Yes, you would have to get the USB adapter as well. $20 is cheaper than I was able to DIY it.
  8. Replies
    178
    Views
    25,348

    Sticky: Yeah, you don't have to connect the rear signal...

    Yeah, you don't have to connect the rear signal wire to the coil. Though if it is connected, you have to ground the plug wire or it fries the coil.

    I'll find the software, at the time it was free,...
  9. Replies
    178
    Views
    25,348

    Sticky: You ordered an Ultima? Lets work through any...

    You ordered an Ultima? Lets work through any issues here, so we can document any/all installation woes.

    If you'd rather, though, you can always hit me up on Facebook. I changed my FB name to...
  10. Replies
    10
    Views
    2,329

    Did they give details? Because that sounds silly....

    Did they give details? Because that sounds silly.

    Adjust your enrichener per my video. You can also power on the motorcycle and watch whether the enrichener closes or not.

    Video link:...
  11. Thread: No spark

    by Jet-Lee
    Replies
    2
    Views
    1,101

    Your BAS sensor could be your issue. Unbolt it...

    Your BAS sensor could be your issue. Unbolt it and shake it around, then put it back at normal position.

    It's a little steel ball inside that can get stuck in a "tipped" position. A good hard...
  12. Replies
    10
    Views
    2,329

    As you tested should still give DC voltage...

    As you tested should still give DC voltage readouts. If you're at zero, your TPS is toast.
  13. Replies
    10
    Views
    2,329

    Are you sure the needle jet (collar) is installed...

    Are you sure the needle jet (collar) is installed in the correct orientation? It's the piece the needle slides into. One end is flat, one is concave. The concave end should be pointing up into the...
  14. Replies
    3
    Views
    641

    "The cnc files" will vary greatly from machine to...

    "The cnc files" will vary greatly from machine to machine.

    If you're meaning the dwg/dwf used to create the cnc files, that should be much easier to find.
  15. Replies
    10
    Views
    2,329

    Sounds like your fuel valve in the carb bowl...

    Sounds like your fuel valve in the carb bowl might be clogged or dirty, not letting enough fuel in. Also check that the bowl vent is clear (top left hole when looking at the carb).
  16. Replies
    5
    Views
    1,820

    I see he put 44903 as his location, that's...

    I see he put 44903 as his location, that's Ontario.
  17. Replies
    5
    Views
    1,820

    Looks clean! Add the Pro-Series and have fun...

    Looks clean!

    Add the Pro-Series and have fun with it!
  18. Replies
    10
    Views
    2,329

    Replace gas with new. Make sure the needle jet...

    Replace gas with new. Make sure the needle jet (collar) is installed in the correct direction. Chech and/or adjust your auto-enricher. Check/adjust your TPS per FSM.

    Links:
    BuellMods for manuals...
  19. Replies
    206
    Views
    163,751

    Sticky: Harley is a bunch of bitches. I would've given...

    Harley is a bunch of bitches.

    I would've given you my VIN, lol.

    Glad you're back in business!
  20. Replies
    635
    Views
    99,196

    Sticky: Poor thing's still sitting. All my attention goes...

    Poor thing's still sitting. All my attention goes to my other bikes, due to them being my rides to/from work.
  21. Replies
    158
    Views
    40,000

    Going to put some 12:1 Wiseco pistons in it. 60k...

    Going to put some 12:1 Wiseco pistons in it. 60k miles on it right now, could use some new rings; need to rebuild the top-end anyways with fresh gaskets.
  22. Replies
    15
    Views
    8,889

    Working on getting the bars lowered. Can't go...

    Working on getting the bars lowered. Can't go with RX top triple as it interferes with the SX dash. Trying to just do some clip-ons while leaving the SX triple, but I may get conflict with my...
  23. Replies
    17
    Views
    4,111

    I've reused them without issue.

    I've reused them without issue.
  24. Replies
    17
    Views
    4,111

    eBay contest? Cool dude!

    eBay contest? Cool dude!
  25. Replies
    17
    Views
    4,111

    Using an XB9 piston with a stock head will run...

    Using an XB9 piston with a stock head will run worse, as the dome and squish are shaped differently.

    I believe the Blast uses a Thunderstorm piston with a Lightning head, so if you find a front...
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4