Search:

Type: Posts; User: Jet-Lee; Keyword(s):

Page 1 of 20 1 2 3 4

Search: Search took 0.12 seconds.

  1. Replies
    202
    Views
    151,221

    Sticky: Harley is a bunch of bitches. I would've given...

    Harley is a bunch of bitches.

    I would've given you my VIN, lol.

    Glad you're back in business!
  2. Replies
    635
    Views
    90,431

    Sticky: Poor thing's still sitting. All my attention goes...

    Poor thing's still sitting. All my attention goes to my other bikes, due to them being my rides to/from work.
  3. Replies
    158
    Views
    32,660

    Going to put some 12:1 Wiseco pistons in it. 60k...

    Going to put some 12:1 Wiseco pistons in it. 60k miles on it right now, could use some new rings; need to rebuild the top-end anyways with fresh gaskets.
  4. Replies
    15
    Views
    7,275

    Working on getting the bars lowered. Can't go...

    Working on getting the bars lowered. Can't go with RX top triple as it interferes with the SX dash. Trying to just do some clip-ons while leaving the SX triple, but I may get conflict with my...
  5. Replies
    17
    Views
    1,875

    I've reused them without issue.

    I've reused them without issue.
  6. Replies
    17
    Views
    1,875

    eBay contest? Cool dude!

    eBay contest? Cool dude!
  7. Replies
    17
    Views
    1,875

    Using an XB9 piston with a stock head will run...

    Using an XB9 piston with a stock head will run worse, as the dome and squish are shaped differently.

    I believe the Blast uses a Thunderstorm piston with a Lightning head, so if you find a front...
  8. Also, here's a PDF of Andrews installation...

    Also, here's a PDF of Andrews installation instructions.

    http://www.andrewsproducts.com/files/assets/Blast-1.pdf
  9. There should be an arrow on the top of the...

    There should be an arrow on the top of the piston. Orient the piston to point towards the front wheel.

    If there is no arrow, then the larger valve relief is the intake, which is at the rear.

    If...
  10. Jumper the kickstand safety switch, flip the...

    Jumper the kickstand safety switch, flip the middle diode in the fuse box and try again.
    If that still doesn't do it, clean all grounds thoroughly.
    If still having the issue after that, then...
  11. DMV messed up, maybe? What's your VIN? My 1988...

    DMV messed up, maybe? What's your VIN?

    My 1988 RX7 was titled and smogged as 87.I pointed out the VIN sticker and asked, "How can it be an 87 if it wasn't produced until Jan 1988?"
  12. Replies
    3
    Views
    1,320

    Wow, didn't realize it's been so long.

    Wow, didn't realize it's been so long.
  13. Replies
    17
    Views
    1,875

    I've always liked the chopper Blasts. I'd...

    I've always liked the chopper Blasts. I'd probably never build or ride one, but I think the builds are neat to follow.
  14. Replies
    15
    Views
    7,275

    Wow, so much has happened since this. I'll piece...

    Wow, so much has happened since this. I'll piece it together...

    The shop, Bay Area Racing (owned and operated by Dean Hodel) did not show up to the court hearing and I won a default judgement. He...
  15. Replies
    20
    Views
    5,540

    Nice. Plug wires can be a real pain to diagnose.

    Nice. Plug wires can be a real pain to diagnose.
  16. Well that was unexpected, lol. Glad it was a...

    Well that was unexpected, lol. Glad it was a simple fix!
  17. Replies
    7
    Views
    8,232

    hot chip-seal will destroy a tire VERY fast

    hot chip-seal will destroy a tire VERY fast
  18. Thread: Stlouis here

    by Jet-Lee
    Replies
    4
    Views
    5,937

    Nice job getting around the spam blocks, with an...

    Nice job getting around the spam blocks, with an email like that.

    Shoot me a PM verifying your information or I will ban you, your email domain, and all IPv4/v6 addresses from which you registered...
  19. Replies
    3
    Views
    3,243

    $500 for parts? Sure.

    $500 for parts? Sure.
  20. I've read this post a dozen times and have yet to...

    I've read this post a dozen times and have yet to respond.

    You need to check if it has the stator that's been drilled for better cooling. If not, buy the upgrade because it's a time bomb.

    The...
  21. Replies
    2
    Views
    3,054

    My Blast dyno'd 31/28 hp/tq, with a hollowed...

    My Blast dyno'd 31/28 hp/tq, with a hollowed stock muffler and open carb...waaay back in like 2008/2009. They're normally like 28/25 hp/tq in stock form.

    It hasn't been dyno'd since.
  22. I fixed your image links. The inline uploader is...

    I fixed your image links. The inline uploader is broken (dunno why), but if you "Go Advanced" you can upload them as attachments.
  23. Replies
    2
    Views
    2,226

    This guy put XB suspension on a Blast frame....

    This guy put XB suspension on a Blast frame.
    http://i250.photobucket.com/albums/gg273/Xbbuell/blast/blast013-1.jpg
  24. Thread: Exhaust wraps

    by Jet-Lee
    Replies
    5
    Views
    8,508

    It traps moisture and contaminants and promotes...

    It traps moisture and contaminants and promotes rust and deterioration of the metal.

    It also hides cracks that cause similar running issues as vacuum leaks, which can cause a troubleshooting...
  25. Replies
    635
    Views
    90,431

    Sticky: I have decided on some big plans for this. Will...

    I have decided on some big plans for this. Will get going once I get my EBR issues solved.
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4